Products
Gasket and Washer Cutters

Gasket and Washer Cutters

Model:KXT GWC
KXT GWC is a manually operated adjustable gasket and washer cutter that cuts outside diameters from 50 mm to 650 mm from non-asbestos, rubber, graphite, PTFE, and cork sheet. The graduated radius arm locks to the required OD, while the hardened steel blade produces a clean, burr-free edge with a single rotation. Replacement blades and pilot pins are stocked separately to extend tool life. Send your material type, sheet thickness, and required OD range for a same-week factory quote.

Adjustable Gasket & Washer Cutter for 50–650 mm Sheet Gaskets

KXT GWC is a manually operated cutter designed for maintenance workshops and gasket fabrication benches that need to produce **round gaskets and washers on demand** rather than hold stock for every flange size. A **graduated radius arm** locks to the required dimension, and a **hardened steel blade** completes a clean cut in a single rotation — on non-asbestos jointing sheet, rubber, graphite, PTFE, and cork. For high-volume or CNC production, compare the Machines for Cutting Gaskets range; for the wider tool family, see Gasket Tools.

Cutting Range: OD 50 mm – 650 mm Radius setting = target OD ÷ 2
50 mm150 mm250 mm350 mm450 mm550 mm650 mm

One tool covers the full DN15–DN600 flange gasket range without changing accessories.

How the Cutter Works — Four Steps

STEP 1 Mark the Centre Punch or mark the gasket centre on the sheet; the pilot pin locates here and keeps the arm anchored through the cut.
STEP 2 Set the Radius Loosen the lock, slide the blade carriage along the graduated arm to the required radius (target OD ÷ 2), and tighten.
STEP 3 Cut the OD Apply steady downward pressure and rotate the arm a full 360° — one rotation produces a clean, burr-free outside diameter.
STEP 4 Cut the Bore Reposition the pilot pin to the bore centre, reset the arm to the inner radius, and rotate to cut the ID. The ring drops free.

Compatible Sheet Materials

Non-Asbestos Jointing SheetStandard compressed fibre sheet used for general flange gaskets — see Non-Asbestos Sheet.
Rubber SheetNBR, EPDM, and silicone rubber sheet for low-pressure and water-service gaskets.
Graphite SheetFlexible graphite sheet for high-temperature and steam service gaskets.
PTFE SheetVirgin and filled PTFE sheet for chemical-resistant gaskets — see PTFE Sheet.
Cork SheetCork and cork-rubber sheet for oil, fuel, and low-pressure sealing gaskets.
Washer BlanksThin sheet in the same materials for cutting washers and spacer rings.

Tool Body, Blade and Spare Parts

Graduated Radius Arm Lockable carriage with engraved metric scale; arm length covers radius settings from 25 mm to 325 mm.
Hardened Steel Blade Replaceable cutting blade; when cutting resistance rises or the edge drags, swap the blade rather than the tool.
Centre Pilot Pin Locates and holds the gasket centre; consumable part, available as a separate spare.
Replacement Blade & Pin Kits Stocked separately so the cutter can be maintained for years instead of replaced when the blade dulls.

Operating Safety & Maintenance

  • Cut on a stable, flat cutting board or sacrificial surface — never on a finished flange face or machine table.
  • Keep fingers clear of the blade path; rotate the arm by the handle grip, not by pushing the blade carriage.
  • Retract or remove the blade before storing the tool, and store in the supplied case where provided.
  • Wipe the graduated arm and pivot with a dry cloth after use on graphite or PTFE sheet; do not use solvent on the scale.
  • Inspect blade and pilot pin before each session; replace when the cut edge becomes ragged or the pin no longer holds centre.

Specification Summary — KXT GWC

Cutting Diameter Range
50 mm to 650 mm outside diameter (radius setting 25–325 mm)
Operation Type
Manual, single-rotation cut
Radius Arm
Graduated with lock carriage
Blade
Hardened steel, replaceable
Centre Locator
Replaceable pilot pin
Compatible Sheet Materials
Non-asbestos jointing sheet, rubber sheet, graphite sheet, PTFE sheet, cork sheet
Compatible Sheet Thickness
Common gasket thicknesses (0.5 mm to 5 mm typical)
Replacement Parts
Blade and pilot pin kits available separately
Body Material
Steel / aluminum body

Procurement FAQ

What outside diameter range can this gasket cutter handle?

KXT GWC covers outside diameters from 50 mm to 650 mm using the graduated radius arm. The blade carriage is set to the target radius (target OD divided by two), and the pilot pin holds the centre of the cut. Both the OD and the inner bore are cut with the same tool.

Which sheet materials is the cutter suitable for?

The cutter is suitable for non-asbestos jointing sheet, rubber, graphite, PTFE, and cork sheet in common gasket thicknesses. For hard or heavily reinforced sheet, or for repetitive production volumes, see the Machines for Cutting Gaskets range.

Are replacement blades and pilot pins available separately?

Yes. Blades and pilot pins are stocked as separate spare parts so the tool can be maintained rather than replaced. Specify the model when ordering spares; see the full tool family in Gasket Tools.

Can the cutter produce ring gaskets with an inner bore?

Yes. Cut the outside diameter first with the arm set to the outer radius, then reposition the pilot pin to the bore centre and reset the arm to the inner radius. Both cuts use the same graduated scale.

What is the lead time and minimum order quantity?

Stock models are available from one piece for sample evaluation. Typical lead time for stock items is 5–10 working days from order confirmation. Production quantities and OEM branding are quoted with a project-specific lead time and volume price.

Need a gasket cutter sample or a factory quote? Tell us your material type, sheet thickness, and required OD range — our technical sales team responds within 2 business hours with the recommended model, spare-part kit, and lead time.
Request Factory Quote
Send Inquiry
Contact Info

Request a Quote or Technical Consultation

Share your sealing requirement and our technical sales team will respond within 24 business hours. For fastest service, include your flange specification, operating pressure, temperature, and process media in the message below.

X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept