Products
PTFE Filament Packing

PTFE Filament Packing

Model:KXT P103
PTFE Filament Packing Braided from sintered and high stretched PTFE multifilament yarns. Within PTFE impregnation. Good resistance to compression and extrusion, high structural and cross-sectional density.
Rating: 5.0
(Rating Count: 1)
Model KXT P103

PTFE Filament Packing for Chemical Pumps, Valve Stems & Plungers

Looking for a braided packing that seals almost every chemical from pH 0 to 14 — while staying clean enough for food, pharma and fine chemical service? PTFE filament packing is braided from sintered and highly-stretched PTFE multifilament yarn, impregnated with PTFE dispersion. The result is a dimensionally stable, high-density braid with low friction, very little water absorption and no asbestos content.

Kaxite PTFE filament packing is most useful in slower shaft speed applications — valve and pump stuffing boxes where chemical resistance matters more than shaft speed. Available in square cross-sections from 3 × 3 mm to 25 × 25 mm, in 5 kg and 10 kg spools, and in pre-formed rings on request.

Send your shaft diameter, media and operating temperature — our technical team replies with a recommendation and price within 2 business hours.

What Buyers Get From Kaxite

Direct factory pricing

Braided, impregnated and spooled in our own workshop. No trading company mark-up between you and the production line. See our workshop.

Clean, asbestos-free material

No asbestos in the raw material or the finished PTFE filament packing. Suitable for chemical, food, pharma and fine chemical service. See our certificates.

Standard and custom sizes

Square sections 3 × 3 mm to 25 × 25 mm from stock. Custom cross-sections, pre-formed rings and die-formed sets produced to your drawing.

Low MOQ, fast response

Single spools accepted for trial and emergency maintenance. Technical reply and quotation within 2 business hours.

Honest lead times

Standard PTFE filament packing normally ships in 7–15 working days. Custom sizes and pre-formed rings quoted against real production capacity. See packaging & shipping.

Quality you can audit

Cross-section, density and braid structure checked on every batch. Third-party inspection (SGS / BV / TUV) supported. See our quality process.

What PTFE Filament Packing Actually Does

PTFE filament packing is braided from sintered and highly-stretched PTFE multifilament yarn, then impregnated with PTFE dispersion. Because the yarn is stretched before braiding, the individual filaments run the full length of the packing — this is what gives the finished braid its higher cross-sectional density and better structural strength than conventional PTFE packing.

The impregnation step does two things at once: it reduces friction between the packing and the shaft, and it fills the gaps between braided strands so leakage through the braid itself is minimised. This is why PTFE filament packing is specified in slower shaft speed applications where a leak-tight, chemically inert seal matters more than high rotary speed.

PTFE filament packing braided from sintered highly stretched PTFE multifilament yarn
Style KXT P103 PTFE filament packing — braided from sintered, highly-stretched PTFE multifilament yarn with PTFE dispersion impregnation.
When PTFE filament is not the right answer: if the shaft speed is above roughly 8 m/s, or if the joint runs dry at high temperature, a graphite PTFE packing or an aramid fiber packing usually performs better. Tell us the shaft speed and medium and we will recommend the correct braid honestly.

Key Specifications

Model
KXT P103
Material
Sintered, highly-stretched PTFE multifilament yarn with PTFE dispersion impregnation
Colour
White
Cross-section
3 × 3 mm to 25 × 25 mm square; other sizes on request
Standard spool
5 kg and 10 kg spools; pre-formed rings available
Density
Approx. 1.4 g/cm³
Temperature range
−150 °C to +280 °C
pH range
0 – 14
Rotary speed (max)
12 m/s
Asbestos content
None — asbestos-free material and process
Lubrication
PTFE dispersion impregnation — no additional oil required
Certificates
Material declaration on request; third-party inspection (SGS / BV / TUV) supported

Pressure and speed limits

Application Maximum pressure Typical use
Rotary pump 30 bar Chemical pumps, transfer pumps, slow-speed shafts
Reciprocating pump 160 bar Plunger pumps, metering pumps, injection pumps
Static sealing 280 bar Valve bonnets, check valves, needle valve stems
Rotary speed (max) 12 m/s Best performance below 8 m/s
Reading these limits: the three pressures are not interchangeable — they describe three different joint types. A packing that seals 280 bar as a static gland seal will only handle 30 bar in a rotary pump. Tell us the joint type and we will quote against the correct limit.

Forms and Sizes Available

PTFE filament packing is supplied in a range of forms depending on the gland. The right form depends on the shaft size, whether the gland can be re-packed in place, and the required number of rings.

Square braid spool

Standard 3 × 3 mm to 25 × 25 mm square braid, supplied on 5 kg or 10 kg spools. Cut to length on site for any gland size.

Pre-formed rings

Die-formed rings cut and shaped to your exact shaft diameter and stuffing box dimensions. Reduced installation time and better ring-to-ring fit.

Die-formed sets

Full gland sets — typically 3 to 7 rings per set — supplied as a matched set with end rings and lantern ring where required.

Custom cross-section

Non-square cross-sections (rectangular, oval) for special glands. Send the drawing or sample and we will confirm feasibility.

Expanded PTFE cord

For larger glands or where a softer, more compressible braid is required, see our expanded PTFE round cord.

Related braids

Other PTFE packing options: pure PTFE packing, PTFE packing with oil and graphite PTFE packing.

Where PTFE Filament Packing Is Used

PTFE filament packing is specified wherever the medium is chemically aggressive and the shaft speed is moderate. Typical installations include:

  • Slower shaft speed applications in pumps and agitators
  • Check valve stems and needle valve stems
  • Safety injection system valves in power and nuclear auxiliary plants
  • Chemical pumps, dosing pumps and transfer pumps
  • Plungers and reciprocating pump rods
  • Oil and petrochemical service where chemical resistance matters
  • Food, pharma and fine chemical service where a clean, asbestos-free braid is required
  • Any gland sealing pH 0–14 media below 280 °C

Related packing materials in the same family include PTFE packing, graphite packing, aramid fiber packing, carbon fiber packing and die-formed graphite rings.

Packing and Shipping

PTFE filament packing is supplied on rigid spools, wrapped in plastic film and packed in cartons or wooden cases suitable for sea and air freight. Pre-formed rings are packed flat with the ring size labelled on the outside of the carton. Customer labels and packing lists are available on request — see packaging & shipping.

Shipping is by sea, rail or air depending on your schedule and destination. Standard PTFE filament packing normally ships within 7–15 working days of order confirmation. Custom cross-sections and die-formed sets are quoted against real production capacity.

Buyer FAQ

What is the difference between PTFE filament packing and standard PTFE packing?

PTFE filament packing is braided from sintered and highly-stretched PTFE multifilament yarn — the fibres run the full length of the packing, giving higher cross-sectional density and structural strength than standard braided PTFE packing. Standard PTFE packing is typically braided from un-stretched yarn.

What temperature and pH range does it handle?

−150 °C to +280 °C, pH 0 to 14. Within that range it is resistant to almost every chemical except molten uranium salts. If your medium is outside this range, contact us — other braids may be more suitable.

What is the maximum shaft speed?

Up to 12 m/s, but the material performs best below about 8 m/s. Above that, consider a graphite PTFE packing or an aramid fiber packing. Tell us your shaft speed and we will recommend the correct braid.

Can you supply pre-formed rings for a specific shaft size?

Yes. Send the shaft diameter, stuffing box ID and depth, and the number of rings required. We produce die-formed rings and full gland sets to those dimensions.

Do you supply material certificates?

Yes. EN 10204 3.1 certificates are available on request, and third-party inspection (SGS, BV, TUV or client-nominated) can be arranged or hosted at additional cost. See our certificates.

What is the minimum order quantity?

No rigid minimum. Single spools and small quantities for shutdown work are accepted at the same unit price structure. Pre-formed rings and die-formed sets are quoted per project.

How quickly can you quote and ship?

Send the cross-section size, quantity, shaft speed, medium and operating temperature. With these details we can give you a technical recommendation and price within 2 business hours. Standard PTFE filament packing normally ships within 7–15 working days of order confirmation.

Request a Quotation for PTFE Filament Packing

Send us your shaft diameter, stuffing box dimensions, medium and operating temperature — or simply a clear photo of the existing packing with a ruler in frame — and we will come back with a technical recommendation, price and realistic delivery date.

Send Inquiry Now
Send Inquiry
Contact Info

Request a Quote or Technical Consultation

Share your sealing requirement and our technical sales team will respond within 24 business hours. For fastest service, include your flange specification, operating pressure, temperature, and process media in the message below.

Rating:
5.0
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept