Products
Non-Asbestos Rubber Gasket

Non-Asbestos Rubber Gasket

Model:KXT 2000
Non-asbestos Rubber Gasket Synthetic Fiber gasket cut from Synthetic Fiber rubber sheet. Suitable for use as an oil-resistant jointing medium for heat installations and engine sealing.
Model KXT 2000 · Aramid Fiber + NBR

Non-Asbestos Rubber Gasket — Aramid Fiber with NBR Binder for Oil, Fuel and Steam Sealing

Non-Asbestos Rubber Gasket (KXT 2000) is an asbestos-free compressed fiber sheet gasket made from aramid fiber reinforcement with NBR (nitrile butadiene rubber) binder. Kaxite manufactures this non-asbestos rubber gasket for flange joints, engine sealing, and general chemical service where asbestos gaskets are banned or undesirable.

KXT 2000 non-asbestos rubber gasket operates from 180 °C to 300 °C, has a density of 1.95 g/cm³ at 1.5 mm thickness, tensile strength of 8 MPa (ASTM F152), and residual stress of 20 MPa (BS 7531). It resists hot oil, fuels, gasoline, gas, hot water, and steam, making the gasket suitable as a replacement for asbestos rubber gaskets in high-temperature, high-pressure sealing.

Request a quote for Non-Asbestos Rubber Gasket KXT 2000 →

Non-Asbestos Rubber Gasket KXT 2000 aramid fiber with NBR binder
180–300 °C Working Temperature
1.95 g/cm³ Density
8 MPa Tensile Strength
Asbestos-Free Environment Friendly
Asbestos Rubber Gasket Legacy material
  • Carcinogenic to humans when fibers are inhaled
  • Banned or restricted in the EU, US and many other markets
  • Disposal is expensive and regulated as hazardous waste
  • Being phased out in most industrial sealing applications
Non-Asbestos Rubber Gasket KXT 2000 — Recommended replacement
  • Harmless to the human body — no asbestos fibers
  • Environment-friendly material, lower disposal cost
  • Higher strength and elasticity than asbestos rubber gasket
  • Strong anti-penetration performance in high temperature and pressure conditions
  • Excellent bolt torque retention and nice sealability

What is a Non-Asbestos Rubber Gasket?

Direct answer: A Non-Asbestos Rubber Gasket is a compressed fiber sheet gasket made from non-asbestos fibers — such as aramid fiber, carbon fiber, graphite or fiberglass — combined with an elastomer binder such as NBR, SBR or EPDM and mineral fillers. It is used to seal flange joints, engine parts and general chemical equipment, and is a direct replacement for asbestos rubber gaskets.

Kaxite Non-Asbestos Rubber Gasket KXT 2000 uses aramid fiber with NBR binder. Aramid fiber provides tensile strength and heat resistance, while the NBR binder delivers oil resistance and elastic recovery. Special adhesives and a small amount of filler are added, then the sheet is rolled and vulcanized (sulfurated). The elastomer composition is selected according to the sealing application — the binder determines the chemical compatibility, the fiber determines the temperature and mechanical limits.

Non-Asbestos Rubber Gasket KXT 2000 aramid fiber with NBR binder sheet
Non-Asbestos Rubber Gasket KXT 2000 — aramid fiber reinforced compressed sheet with NBR binder, 1.5 mm standard thickness, black finish, cut to flange or engine sealing shape.

Why choose Kaxite Non-Asbestos Rubber Gasket KXT 2000?

Harmless to the Human Body

Contains no asbestos fibers, unlike asbestos rubber gaskets. Safe to handle, cut and install without respiratory protection.

High Temperature and Pressure Resistant

Working temperature range 180–300 °C, with strong anti-penetration performance in high-temperature and high-pressure flange joints.

Good Resistance to Hot Oil and Fuels

NBR binder resists hot oil, gasoline, fuel and gas. ASTM Oil 1 thickness increase only 1.0%, ASTM Oil 3 and Fuel B both 4.0%.

Nice Sealability and Seamless Effect

Gas leakage below 1.0 ml/min under BS 7531 test. Compression above 6% and recovery 50% minimum ensure reliable sealing after bolt torque.

Excellent Bolt Torque Retention

Residual stress 20 MPa (BS 7531). The gasket retains bolt load over thermal cycling, reducing re-torque requirements in service.

Environment Protection and Good Tensile Strength

Non-hazardous disposal, lower waste cost than asbestos. Tensile strength 8 MPa (ASTM F152) supports cutting into complex gasket shapes.

Non-Asbestos Rubber Gasket KXT 2000 — Physical Properties

Direct answer: KXT 2000 Non-Asbestos Rubber Gasket is supplied in 1.5 mm standard thickness with density 1.95 g/cm³, tensile strength 8 MPa, compression above 6%, recovery 50% minimum, residual stress 20 MPa, gas leakage below 1.0 ml/min, and a working temperature range of 180–300 °C.
Property Test Standard Value
Thickness — 1.5 mm
Density — 1.95 g/cm³
Tensile Strength ASTM F152 8 MPa
Compression ASTM F36 > 6 %
Recovery ASTM F36 50 % min
Residual Stress BS 7531 20 MPa
Gas Leakage BS 7531 < 1.0 ml/min
ASTM Oil 1 — Thickness Increase ASTM Oil 1 1.0 %
ASTM Oil 3 — Thickness Increase ASTM Oil 3 4.0 %
ASTM Fuel B — Thickness Increase ASTM Fuel B 4.0 %
Working Temperature — 180 – 300 °C
Fiber Reinforcement — Aramid Fiber
Binder — NBR (Nitrile Butadiene Rubber)

Standard supply: 1.5 mm thickness, 1.5 m × 1.5 m sheet or cut gasket. Other thicknesses and sheet sizes available on request. Test certificates available for BS 7531 and ASTM F36.

Where is Non-Asbestos Rubber Gasket KXT 2000 used?

Direct answer: KXT 2000 Non-Asbestos Rubber Gasket is used in pipe flange joints, steam service, motorcycle engines, general chemical equipment, gasoline and gas pipelines, hot water systems, and oil or fuel lines. It replaces asbestos rubber gaskets in every high-temperature, high-pressure joint.
Pipe Flange Joints

Standard pipe flange joints in steam, hot water and chemical pipelines where asbestos-free sealing is required.

Steam Service

Steam line flanges and steam valve bonnets up to 300 °C working temperature, with good bolt torque retention.

Motorcycle Engine

Engine cover gaskets, crankcase joints and exhaust flange gaskets where oil and fuel resistance is required.

General Chemical

Chemical plant flange joints handling gas, hot water, oil and fuel where a low-leakage compressed fiber gasket is needed.

Gasoline and Gas

Fuel distribution flanges and gas pipeline joints. ASTM Fuel B thickness increase is only 4.0%.

Asbestos Replacement

Direct retrofit for asbestos rubber gaskets in existing flanges, with same or better sealing performance.

Frequently asked questions about Non-Asbestos Rubber Gasket

Q1What is a Non-Asbestos Rubber Gasket?

A Non-Asbestos Rubber Gasket is a compressed fiber sheet gasket made from non-asbestos fibers such as aramid, carbon or fiberglass, combined with an elastomer binder such as NBR and mineral fillers. It seals flanges, engines and chemical equipment, and is a safe replacement for asbestos rubber gaskets.

Q2Can Non-Asbestos Rubber Gasket replace an asbestos rubber gasket directly?

Yes. Kaxite Non-Asbestos Rubber Gasket KXT 2000 is designed as a direct replacement for asbestos rubber gaskets. It has higher strength and elasticity, strong anti-penetration performance in high-temperature and high-pressure conditions, and does not contain asbestos fibers. Existing flange dimensions and bolt loads usually do not require changes.

Q3What is the maximum working temperature of Non-Asbestos Rubber Gasket KXT 2000?

The working temperature range of KXT 2000 is 180 °C to 300 °C. The upper limit depends on the actual fluid, flange pressure, bolt load and continuous or intermittent service. For continuous steam above 250 °C, confirm with the Kaxite technical team before ordering.

Q4What media does Non-Asbestos Rubber Gasket resist?

KXT 2000 resists hot oil, gasoline, fuel, gas, hot water and steam. ASTM Oil 1 thickness increase is 1.0%, ASTM Oil 3 is 4.0%, and ASTM Fuel B is 4.0%. For strong acids, strong alkalis or solvents, contact Kaxite for a material recommendation.

Q5What is the standard thickness and sheet size?

KXT 2000 is supplied in 1.5 mm standard thickness, in 1.5 m × 1.5 m sheet or cut to your gasket drawing. Other thicknesses — 0.5 mm, 1.0 mm, 2.0 mm, 3.0 mm — and custom sheet sizes are available on request.

Q6Is Non-Asbestos Rubber Gasket food-safe or drinking-water safe?

KXT 2000 is an industrial sealing grade material. For food-contact or drinking-water applications, ask Kaxite for a food-grade or WRAS-approved non-asbestos gasket material. Do not use standard KXT 2000 in potable water systems without confirmation.

Q7What is the gas leakage rate of KXT 2000?

Gas leakage is below 1.0 ml/min under the BS 7531 test method, at the standard test gasket stress. This makes KXT 2000 suitable for gas and steam flange joints where low leakage is required.

Q8How is Non-Asbestos Rubber Gasket different from Non-Asbestos Sheet?

Non-Asbestos Rubber Gasket KXT 2000 is a specific aramid-fiber NBR-binder grade optimized for oil, fuel, gas, steam and hot water service. Non-Asbestos Sheet is a broader material family that includes graphite, glass fiber, aramid and other binder systems. See the Non-Asbestos Sheet page for the full range.

Q9What is the MOQ and lead time for Non-Asbestos Rubber Gasket?

MOQ depends on thickness and sheet size. Sample lead time is typically 5–7 days. Production lead time for standard and custom orders is typically 15–25 days after order confirmation.

Q10Can Kaxite supply Non-Asbestos Rubber Gasket in custom shapes?

Yes. Kaxite cuts Non-Asbestos Rubber Gasket KXT 2000 into flange gaskets, engine gaskets, and custom shapes to customer drawings. Provide inner diameter, outer diameter, thickness and bolt hole pattern for a custom quotation.

Related gasket materials from Kaxite

Why choose Kaxite for Non-Asbestos Rubber Gasket?

10+ Years of Experience Ningbo Kaxite Sealing Materials Co., Ltd. has more than a decade of sealing materials production experience.
Complete Non-Asbestos Range Aramid, carbon, glass fiber and graphite non-asbestos gasket materials — one supplier for all asbestos replacement needs.
Test Certificates Available BS 7531 and ASTM F36 test certificates available on request for KXT 2000 batches.
Sheet and Custom Cut Supplied as 1.5 m × 1.5 m sheet or cut to your flange and engine gasket drawing.

Request a quote for Non-Asbestos Rubber Gasket KXT 2000

Send us your thickness (0.5–3.0 mm), sheet size or gasket drawing, working medium (oil, fuel, gas, steam, hot water), operating temperature and pressure. Kaxite's technical team will respond within 2 business hours with pricing and lead time. For custom-cut gaskets, include inner diameter, outer diameter, thickness and bolt hole pattern.

Last reviewed: September 2026 · Kaxite Sealing Technical Team

Send Inquiry
Contact Info

Request a Quote or Technical Consultation

Share your sealing requirement and our technical sales team will respond within 24 business hours. For fastest service, include your flange specification, operating pressure, temperature, and process media in the message below.

X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept